VEVOR Laser Power Supply Co2 Engraver 60W For Cutting Machine Engraving Supplies

  

This power supply uses a zero-current half-bridge soft switching circuit, which makes the power supply highly efficient and fast in response. Suitable for high and low-level signals. Use the TTL level to control the laser start and stop.

At the same time, a protection switch is added to detect whether there is water or ventilation outside. The laser power adjustment can input 0 to 5V analog signals, can also input PWM signals.

The power supply has an open circuit protection function, which can avoid damage to the laser power supply due to the burst of the laser tube. Each power supply will be subjected to a high temperature 60 ° C 12-hour aging test under full load, and the power supply test will be started and stopped 500 times in 7 seconds.

Fast response speed, good effect, high performance, high cutting power, and it can extend the life of the laser tube. The laser power supply machine starts and stop can be easily controlled by the TTL level. Two methods to adjust laser power: Input 0V to 5V analog signal, can also input the PWN signal. Each data is marked for your convenience. Power detection instructions: When the power is in standby, press the test switch.

If the "L" light is on, the "P" light is on, and the laser tube does not output laser light, the laser tube is broken. If the laser tube outputs laser light, the laser power is normal; if the laser light is off, it means that the laser power supply is broken. Open circuit protection function, it can be used to detect the presence or absence of waterway, protect the laser.

It can better protect the laser power and prolong the service life. Co2 laser engraver power supply is s.

Uitable for a variety of CO2 laser tubes. The CO2 laser power supply is small in size, light in weight, easy to operate, and has a good matching performance with the laser tube, which can be directly connected to the laser tube. Fast response speed, good effect, high performance, high cutting power, and can extend the life of the laser tube. Input Voltage: AC110V / AC220V. Gross Weight:2.3kg/5.09lbs.

Package Size: 27x20x14cm/10.62x7.87x5.51inch. High Voltage Pack (Including a High Voltage Head and a High Voltage Wire). 1 x Laser Power Supply (60W). 7.08 kg (15.61 lbs). 14.5 kg (31.961 lbs).

16.46 kg (36.281 lbs). 18.67 kg (41.161 lbs). 12.84 kg (28.31 lbs). We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you.

Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us.

7:00am-13:00pm (Berlin Time). International Buyers - Please Note. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage.

Used items will not be accepted for return. All emails will be responded to within 12-24hours.

Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's your fault. Open circuit protection function, it can be used to detect the presence or absence of waterway, protect the laser; It can better protect the laser power and prolong the service life. Co2 laser engraver power supply is suitable for a variety of CO2 laser tubes. If you have any changes, pls inform us 7:00am-13:00pm (Berlin Time) in the same day.

This item is in the category "Business, Office & Industrial\Electrical Equipment & Supplies\Power Supplies\Switching Mode Power Supplies". The seller is "shuqhk4" and is located in this country: GB. This item can be shipped worldwide.

1. Material: Iron, ABS Plastic
2. Type: Switching Power Supply
3. Brand: VEVOR
4. MPN: WLKJL008871575869379
5. Custom Bundle: No
6. Modified Item: No
7. Lettering Type: Removable
8. Power: 60W
9. Input Voltage: AC110V / AC220V
10. Maximum Output Voltage: 24KV
11. Maximum Output Current: 25mA
12. Response Speed: ≤1ms
13. Cooling Method: Fan Cooling
14. Gross Weight: 2.3kg/5.09lbs
15. Package Size: 27x20x14cm/10.62x7.87x5.51inch
16. Features: Universal Input
17. Colour: Black
18. Installation Area: Laser Engraver Machine
19. Efficiency: 91%
20. Item Width: 20cm
21. Nominal Current Rating: 25mA
22. Nominal Voltage Rating (AC): 220 V
23. Nominal Power Rating: 60W
24. Item Height: 14cm
25. Protection Properties: Overcurrent Protection,Overload Protection
26. EAN: 08085443126229